RAS1

Multiple RF active splitters/combiners
Ultra wide band = 50-3.000 MHz

ROVER RAS1 front
  • Especially designed for SATCOM SYSTEM INTEGRATOR
  • Meets strict specifications like: OIP3, R.L. and Flatness
  • Up to 4 RF Input Swappable Plug-in Amplifier, or 1 Optical Input Receiver and up-to 3 RF Input
  • SPLITTER/COMBINER PORT per SLOT:
    • N.1 RF IN/OUT port with 10 MHz & DC PASS
    • N.1 RF OUT/IN port with 10 MHz PASS
    • N.3 RF OUT/IN port with Blocked DC
  • 10 dB switchable RF Attenuator
  • Available optional RF connectors: F, SMA, BNC 75 & 50 ohm
  • Available Optional Optical Connectors: SC-APC, LC-APC, E2000, FC-APC
  • Redundant PSU from 2 different Power lines
  • Dry contact Alarm for: RF Power Sensor, PSU and LNBs
  • Fully compatible with all existing System

BENEFIT

  • Ultra WIDE BAND 50-3.000 MHz flat
  • Especially designed for the NEW Extended LNBs band: 250-2.350 MHz, (only 1 coax cable for the entire V. or H. Polarization Band)
  • Splitter & Combiner function, all in 1 U 19” Rack
  • Easy assembly and fully configurable, from 1 Input to 4 Outputs, up to 4 Inputs to 32 Outputs
  • 10 MHz Reference PASS at all SLOTS
  • Optical Input with AGC RX module (opt.)
  • Each Plug-in RF Input Amplifier have on front panel:
    • RF Monitor Port, LNB Power Control, 10 dB RF Attenuator
    • LED for RF Sensor, LNBs and Power Supply Alarms
  • Full Custom expandable and rack space optimization
  • Intuitive and self-explaining descriptions labels, for Connector, LEDs and Switches

ROVER RAS1 and RAC1 v7i s-02

RF PORT CAPACITY:

  • Input Port Number: 1, 2, 3 or 4 (all Swappable Plug-In module)
  • Output Port Number: 4, 8, 12, 16, 20, 24, 28, 31 or 32 (8 slots, 4 way each slot)
  • Optical Input port Number: 1 (SC-APC, LC-APC, E2000, FC-APC opt.)
  • 10 MHz Reference PASS (through dedicated port N. 1)

RF SPECIFICATIONS:

  • Frequency Range = 50-3.000 MHz
  • Connectors = F (or BNC or SMA opt.)
  • Impedance = 75 Ohm (or 50 Ohm opt.)
  • IP dB = 0 dBm
  • OP dB = 0 dBm
  • Damage Input Level = 15 dBm
  • Input R.L. = >16 dB, 14 dB min.
  • Output R.L. = >16 dB, 14 dB min.
  • Total Gain/Loss = 0 dB, ± 1,5 dB typ, 2 dB max
  • Temperature gain variation = 1,5 dB from -30° to +60° C
  • L Band Flatness = ± 1 dB, 1,5 dB max
  • Full Band Flatness = ± 1,5 dB, 2 dB max
  • Flatness in 36 Mhz interval = ± 0,3 dB, 0,5 dB max
  • Isolation between adjacent out Port = > 24 dB, 24 min.
  • IMD = > – 40 dB (2 Tones at -13 dBm)
  • Noise Figure = 9 dB

RF INPUT MONITOR PORT:

  • Level = 20 dB down the Input Level
  • Connector = SMA
  • Impedance = 50 Ω
  • Flatness = ± 2 dB

LNB POWER CONTROL (on each AS1 INPUT AMPLIF.):

  • D.C. VOLTAGE = OFF, 13V, 18V (or 24 optional) max 600 mA for each Input
  • TONE = 22 KHz ON/OFF
  • LED = green = OK, red = dc short circuit Alarm
  • ALARM INDICATION = Via LED and dry contact

RF POWER SENSING:

  • POWER THRESHOLD = – 45 dBm (RMS)
  • ALARM INDICATION = LED (and dry contact alarm)

DRY CONTACT ALARM BOARD:

  • CONNECTOR = SUB-D9 Male
  • CONTACT LOAD = 65 V – 400 mA
  • A & B MAINS PSU = one defective or both
  • LNB = dc Short Circuit
  • RF POWER SENSING = RF TOO LOW or NO RF Signal

REDUNDANT POWER SUPPLY:

  • N. 2 AC MAINS PSU = 110-240 VAC (with 2 separate receptacle for 2 separate Power LINE)
  • AC POWER CONSUMPTION = < 25 VA
  • N. 1 EXT DC PSU = 48 V D.C. (optional)

GENERAL SPECIFICATIONS:

  • SLIM CASE = 19” 1U Rack (43 cm deep)
  • NET WEIGHT = from 3 to 5 Kg related to the IN/OUT modules
  • SAFETY = EN 50 083-1 and EN 60 950.
  • ENVIRONMENT:
    • Temperature range: –30° / + 55° (max 60°)
    • Umidity 95%
  • EMC = EN 50 083-2

ROVER RAS1 and RAC1 v7i s-04

ROVER RAS1 and RAC1 v7i s-07

ROVER RAS1 and RAC1 v7i s-08

ROVER RAS1 and RAC1 v7i s-09

ROVER RAS1 and RAC1 v7i s-10

ROVER RAS1 and RAC1 v7i s-11

ROVER RAS1 and RAC1 v7i s-12

Download